Skip to content

Basic Exciters

The simplest excitation models: a constant field voltage, a first-order regulator, and the regulator of the Kundur two-area system. CONSTANT and 1ST_ORDER are built in and written in uppercase with no prefix; kundur is registered, and RAMSES adds the exc_ prefix automatically.

The EXC sub-record these models are entered with, and the table of IEEE model variants, are on the Exciter Models page.

The data-file model name is CONSTANT.

The exc_constant model provides a constant field voltage source. The field voltage VfV_f is fixed at its load-flow initialisation value and does not respond to any input:

Vf(t)=Vf0∀tV_f(t) = V_{f0} \quad \forall t

The single algebraic state satisfies:

f(1)=x(1)−Vf0=0f(1) = x(1) - V_{f0} = 0

This model is useful for open-loop tests, for machines that are not equipped with a voltage regulator, or as a placeholder during model development.

Implementation details (from Fortran source):

  • nbxvar = 1, nbzvar = 0, nbdata = 0
  • One additional parameter: prm(1) = Vf0 (set at initialisation from the load-flow field voltage)
  • Observables: vf, if
ParameterDescription
(none)No user-supplied data parameters. The field voltage is taken from the initialisation (load-flow) value automatically.
Show the data record
SYNC_MACH GEN1 BUS1
# FP FQ P Q: share of the power-flow injection (FP, FQ) or initial power (P in MW, Q in Mvar)
1. 1. 0. 0.
# SNOM: Nominal apparent power, used as base power in the machine model (MVA)
600.
# Pnom: Nominal active power of the turbine, used as base power for the turbine model (MW)
570.
# H: Inertia constant (s)
3.
# D: Damping coefficient (usually set to zero when the damper windings are modelled) (pu)
0.
# IBRATIO: Field current base ratio I_fB^mac/I_fB^exc (see above) (pu)
0.95
# TYPE_MOD: Parameter format keyword: RL or XT (case-insensitive)
XT
# Xl: Leakage reactance L_l (pu)
0.15
# Xd: d-axis synchronous reactance (pu)
1.1
# X'd: d-axis transient reactance (must be smaller than Xd) (pu)
0.25
# X"d: d-axis subtransient reactance (pu)
0.2
# Xq: q-axis synchronous reactance (pu)
0.7
# X'q: q-axis transient reactance (pu)
*
# X"q: q-axis subtransient reactance (pu)
0.2
# m: Saturation coefficient (set to 0 to neglect saturation)
0.1
# n: Saturation exponent (ignored when m = 0)
6.0257
# Ra: Armature resistance (pu)
0.
# T'do: d-axis open-circuit transient time constant (s)
5.00
# T"do: d-axis open-circuit subtransient time constant (s)
0.05
# T'qo: q-axis open-circuit transient time constant (s)
*
# T"qo: q-axis open-circuit subtransient time constant (s)
0.1
EXC CONSTANT
TOR CONSTANT
;

The data-file model name is 1ST_ORDER (uppercase, with the underscore).

The exc_1storder model is a first-order automatic voltage regulator (AVR). It represents the simplest dynamic exciter: a proportional gain KAK_A acting on the terminal voltage error, filtered through a single first-order lag TAT_A, with output limits.

The AVR computes the voltage error and drives the field voltage:

dVfdt=1TA[KA(Vref−V)−Vf],Vf∈[Vf,min, Vf,max]\frac{d V_f}{dt} = \frac{1}{T_A}\left[K_A\left(V_{ref} - V\right) - V_f\right], \quad V_f \in [V_{f,min},\, V_{f,max}]

The reference voltage VrefV_{ref} is initialised from:

Vref=V0+Vf0KAV_{ref} = V_0 + \frac{V_{f0}}{K_A}

Implementation details (from Fortran source):

  • nbxvar = 1, nbzvar = 1, nbdata = 4
  • Parameters: prm(1) = KA, prm(2) = TA, prm(3) = Vfmin, prm(4) = Vfmax
  • Additional parameter: prm(5) = V0 (voltage setpoint, computed at initialisation)
  • The ODE in the continuous mode is:
f(1)=−Vf+KA(Vref−V)TAf(1) = \frac{-V_f + K_A(V_{ref} - V)}{T_A}
  • With anti-windup: if the limiter is active, f(1) = Vf - Vfmin (or Vfmax).
1ST_ORDER exciter block diagram. The terminal voltage V is subtracted from the reference Vref and the error drives a first-order automatic voltage regulator of gain KA and time constant TA, limited between Vfmin and Vfmax, giving the field voltage vf. Vref is initialised as V0 plus Vf0 over KA. 1ST_ORDER exciter block diagram. The terminal voltage V is subtracted from the reference Vref and the error drives a first-order automatic voltage regulator of gain KA and time constant TA, limited between Vfmin and Vfmax, giving the field voltage vf. Vref is initialised as V0 plus Vf0 over KA.
ParameterDescription
KAAVR gain (pu/pu)
TAAVR time constant (s)
VfminMinimum field voltage (pu)
VfmaxMaximum field voltage (pu)
Show the data record
SYNC_MACH GEN1 BUS1
# FP FQ P Q: share of the power-flow injection (FP, FQ) or initial power (P in MW, Q in Mvar)
1. 1. 0. 0.
# SNOM: Nominal apparent power, used as base power in the machine model (MVA)
600.
# Pnom: Nominal active power of the turbine, used as base power for the turbine model (MW)
570.
# H: Inertia constant (s)
3.
# D: Damping coefficient (usually set to zero when the damper windings are modelled) (pu)
0.
# IBRATIO: Field current base ratio I_fB^mac/I_fB^exc (see above) (pu)
0.95
# TYPE_MOD: Parameter format keyword: RL or XT (case-insensitive)
XT
# Xl: Leakage reactance L_l (pu)
0.15
# Xd: d-axis synchronous reactance (pu)
1.1
# X'd: d-axis transient reactance (must be smaller than Xd) (pu)
0.25
# X"d: d-axis subtransient reactance (pu)
0.2
# Xq: q-axis synchronous reactance (pu)
0.7
# X'q: q-axis transient reactance (pu)
*
# X"q: q-axis subtransient reactance (pu)
0.2
# m: Saturation coefficient (set to 0 to neglect saturation)
0.1
# n: Saturation exponent (ignored when m = 0)
6.0257
# Ra: Armature resistance (pu)
0.
# T'do: d-axis open-circuit transient time constant (s)
5.00
# T"do: d-axis open-circuit subtransient time constant (s)
0.05
# T'qo: q-axis open-circuit transient time constant (s)
*
# T"qo: q-axis open-circuit subtransient time constant (s)
0.1
EXC 1ST_ORDER
# KA: AVR gain (pu/pu)
200.0
# TA: AVR time constant (s)
0.05
# Vfmin: Minimum field voltage (pu)
0.0
# Vfmax: Maximum field voltage (pu)
6.0
TOR CONSTANT
;

The data-file model name is kundur or exc_kundur. The exc_ prefix is added automatically.

The exc_kundur model implements the excitation system from Kundur’s textbook (Power System Stability and Control, 1994). It includes a first-order voltage transducer, a proportional AVR with transient gain reduction (TGR), and a two-stage PSS acting on rotor speed deviation.

Voltage transducer:

dVfildt=1TR(V−Vfil)\frac{d V_{fil}}{dt} = \frac{1}{T_R}(V - V_{fil})

AVR with transient gain reduction (lead–lag):

Vf(s)=KA⋅1+sTA1+sTB⋅(Vref−Vfil+Vs)V_f(s) = K_A \cdot \frac{1 + s T_A}{1 + s T_B} \cdot \left(V_{ref} - V_{fil} + V_s\right)

where Vref=V+Vf/KAV_{ref} = V + V_f / K_A is computed at initialisation and VsV_s is the PSS output.

PSS (two-stage lead–lag with washout):

xwash(s)=KSTAB⋅sTW1+sTW⋅ω(s)x_{wash}(s) = \frac{K_{STAB} \cdot s T_W}{1 + s T_W} \cdot \omega(s) Vs(s)=1+sT11+sT2⋅1+sT31+sT4⋅xwash(s)V_s(s) = \frac{1 + s T_1}{1 + s T_2} \cdot \frac{1 + s T_3}{1 + s T_4} \cdot x_{wash}(s)

This is the standard two-stage phase-compensating PSS structure. The CODEGEN blocks in the .txt file are:

BlockCODEGEN typeFunction
Voltage filtertf1p1/(1+sTR)1/(1+sT_R)
Main summing junctionalgeqVref−Vfil+Vs−dvV_{ref} - V_{fil} + V_s - dv
AVR (TGR)tf1p1zKA(1+sTA)/(1+sTB)K_A(1+sT_A)/(1+sT_B)
PSS washouttfder1pKSTAB⋅sTW/(1+sTW)K_{STAB} \cdot sT_W/(1+sT_W)
PSS lead–lag 1tf1p1z(1+sT1)/(1+sT2)(1+sT_1)/(1+sT_2)
PSS lead–lag 2tf1p1z(1+sT3)/(1+sT4)(1+sT_3)/(1+sT_4)
exc_kundur block diagram. The terminal voltage passes a transducer of time constant TR to give Vfil, which is subtracted from Vref and summed with the stabiliser output Vs. That error drives an automatic voltage regulator of gain KA with transient gain reduction, a lead-lag with zero TA and pole TB, giving the field voltage vf. The stabiliser takes rotor speed through a washout of gain KSTAB and time constant TW and two lead-lag stages with time constants T1 to T4. exc_kundur block diagram. The terminal voltage passes a transducer of time constant TR to give Vfil, which is subtracted from Vref and summed with the stabiliser output Vs. That error drives an automatic voltage regulator of gain KA with transient gain reduction, a lead-lag with zero TA and pole TB, giving the field voltage vf. The stabiliser takes rotor speed through a washout of gain KSTAB and time constant TW and two lead-lag stages with time constants T1 to T4.
ParameterDescription
TRVoltage measurement filter time constant (s)
KAAVR gain (pu/pu)
TATGR lead time constant (s)
TBTGR lag time constant (s)
KSTABPSS gain
TWPSS washout time constant (s)
T1PSS first lead–lag zero time constant (s)
T2PSS first lead–lag pole time constant (s)
T3PSS second lead–lag zero time constant (s)
T4PSS second lead–lag pole time constant (s)

Computed at initialisation: Vref = V + Vf / KA

Show the data record
SYNC_MACH GEN1 BUS1
# FP FQ P Q: share of the power-flow injection (FP, FQ) or initial power (P in MW, Q in Mvar)
1. 1. 0. 0.
# SNOM: Nominal apparent power, used as base power in the machine model (MVA)
600.
# Pnom: Nominal active power of the turbine, used as base power for the turbine model (MW)
570.
# H: Inertia constant (s)
3.
# D: Damping coefficient (usually set to zero when the damper windings are modelled) (pu)
0.
# IBRATIO: Field current base ratio I_fB^mac/I_fB^exc (see above) (pu)
0.95
# TYPE_MOD: Parameter format keyword: RL or XT (case-insensitive)
XT
# Xl: Leakage reactance L_l (pu)
0.15
# Xd: d-axis synchronous reactance (pu)
1.1
# X'd: d-axis transient reactance (must be smaller than Xd) (pu)
0.25
# X"d: d-axis subtransient reactance (pu)
0.2
# Xq: q-axis synchronous reactance (pu)
0.7
# X'q: q-axis transient reactance (pu)
*
# X"q: q-axis subtransient reactance (pu)
0.2
# m: Saturation coefficient (set to 0 to neglect saturation)
0.1
# n: Saturation exponent (ignored when m = 0)
6.0257
# Ra: Armature resistance (pu)
0.
# T'do: d-axis open-circuit transient time constant (s)
5.00
# T"do: d-axis open-circuit subtransient time constant (s)
0.05
# T'qo: q-axis open-circuit transient time constant (s)
*
# T"qo: q-axis open-circuit subtransient time constant (s)
0.1
EXC kundur
# TR: Voltage measurement time constant (s)
0.02
# KA: AVR gain (pu/pu)
200.0
# TA: Transient gain reduction lead time constant (s)
0.02
# TB: Transient gain reduction lag time constant (s)
10.0
# KSTAB: PSS gain (pu/pu)
9.5
# TW: PSS washout time constant (s)
1.41
# T1: PSS first lead-lag numerator time constant (s)
0.154
# T2: PSS first lead-lag denominator time constant (s)
0.033
# T3: PSS second lead-lag numerator time constant (s)
0.154
# T4: PSS second lead-lag denominator time constant (s)
0.033
TOR CONSTANT
;